Descrizione

SI8125 T Two Component Clear Silicone Potting Adhesive for Electronics Insulation PCB Fixed LED

∎Product Description

SI8125 T A/B is used in potting protection of varied components. It can vulcanize to deep layer. The two components have a good fluidity after mixing. The operation time can be adjusted with the proportion of hardener part B. It can bond well with most materials without using any primer. It can be used to fix the accessories to resist water, dust and leakage of electricity.

∎Typical Applications

• Used for Automotive electronics, modules like Power control modules, Solar modules, Junction box, LED spotlight, Wall washer light, Strip lights, LED fluorescent lamp, etc.

• Electronic potting glue is mainly used for fixing, sealing, potting and coating protection of electronic components, and plays the role of waterproof, moisture-proof, dust-proof, corrosion-proof and shock-proof. In recent years, with the development of the electronic and electrical industry, people pay more attention to the stability of products. In order to protect electronic products from the erosion of the natural environment and prolong their service life, stricter requirements are put forward for the weather resistance, heat dissipation, earthquake resistance and waterproofness of electronic products

• 

∎Technical Data Table

∎Key Features

1. • Two-component high transparency liquid silicone rubber, condensation dealcoholization type

   • Low viscosity, easy to process and operate

   • Low hardening condensation, no corrosion and stressless

   • Excellent electric insulativity and stability in high temperature

   • Excellent bonding ability, good water-proof and moisture-proof property

∎Packing Specification

• Part A：20kg/plastic drum

• Part B：2 kg/plastic drum

• 22kg per set

∎Trasporto e stoccaggio

• When stored at or below 35°C in the original unopened containers, this product has a usable life of 12 months from the date of production.

• Sampling test is necessary for products which exceed shelf life before taking use. During storage may have little settlement stratification, stirring evenly when use, does not affect performance.

It’s non-dangerous goods, can be transported as normal chemicals, CAUTION leakage during transport.

.∎Directions for Use

1. Mix Part A and Part B by 100:10 mass ratio, after evenly mixed, pouring directly into the components or modules as per requirements. It’s recommended to slowly pour along the walls of the implements, so as to reduce the bubbles happens.Still the potted component to let out the bubbles. Vacuum defoaming process of the mixture before potting can improve the performance.

∎Attention of operation

• Keep away from Children

• Avoid contact with eyes and skin. If contact with your skin, scrub first with soap wateror alcohol, then rinse with water. If contact with your eyes, rinse with plenty of water, andseek medical treatment immediately.

• It is forbidden to build on the surface of the wet substrate.

•  Typical Applications

  Applications	LED modules \Lamps	PV modules/Junction box	Automobile / Power modules
  Operation time，min	50	25	45
  Curing time，hour	5	L2.5	5

   

∎Safety Operation Data

MSDS isn’t included here. Please read TDS, MSDS and label carefully before operation. You can get MSDS from MAXTECH or other distributors, or mail to service center maxtech@shmaxtech.com

∎Warranty and Liability

All product properties and application details based on information believe to be reliable and accurate. But you still need to test its property and safety before application. The advice we supply don’t apply in any circumstances. MAXTECH don’t make assurance of any other applications outside the specification until MAXTECH supply a special written guarantee. MAXTECH is only responsible to replace or refund if this product is defective within the warranty period stated above. MAXTECH makes it clear that will not be liable of any accidents.

∎FAQ

• D : In quanto tempo posso ottenere un preventivo?

  R: L'offerta può essere fornita entro e non oltre le 24 ore, a condizione di conoscere tutti i requisiti dettagliati.

  D: Accettate etichette private?

  A: Sì. ODM e OEM sono i benvenuti

  D: Possiamo avere un campione prima dell'ordine?

  A: Of course. Generally, we provide 100-200g free samples for quality testing and the courier fee be born by customers. Thanks for your understanding.

  Q: Avete MOQ?

  A: Yes, Generally ,MOQ is1000-2000kg
  D: In quanto tempo finirà il mio ordine?

  A: It’s depend on your order quantity. Generally, we just need around 10 days to produce 5000kg after receive your
  pagamento.
  D: Come trovare il sigillante adatto?

  A: Please let me know your application purpose,substrate, application method and all your requirements. We would like give you a recommendation.